@lucommodoreil joystick (sempre se dopo una prova mi ci piace) sporgerà dal case di pochi millimetri, il guisto per poterlo pilotare con il pollice in maniera naturale mentre tieni in mano tutto " l'aggeggio ".Ovviamente poi saranno espeste due porte joystick per giocarci in compagnia, ma quando sei da solo non hai neanche bisogno di portarti dietro il joystick perchè sarebbe incorporato
Ed è tutto nato da un semplice gesto, uno scambio e.. Scatta la follia bovina!!! Let the Ox run wild!
Graphics- NTSC (DTV2 and later: NTSC/PAL on chip, only PAL wired in end-market devices)- reprogrammable palette with 4 bits of luma and 4 bits of chroma- DTV2 and later: "chunky" 256 color mode, additional blitter for fast image transformationSound- no support for SID filters <<== (MOLTO MALE!)- DTV2 and later: 8 bit digital sound, additional options for envelope generatorsMemory- DTV1: 128 KB RAM, 2 MB ROM- DTV2 and later: 2 MB RAM, 2 MB flash memory- DMA engine for RAM/RAM and ROM/RAM transfers- DTV2 and later: additional RAM access using bank switching and blitterCPU- implementing a 6510 at 1 MHz- DTV2 and later: Enhanced CPU (fast/burst mode, additional registers and opcodes, support for illegal ops of the 6510)
Features: - ZEE colorfix - fast load : based on "dtv speed load" (thanks to TLR !) 25x load speed, but works only with device 8 ! Only tested with 1541 (I + II), 1571 and 1541 Ultimate. loads everything into ram under the roms and the IO. can load up to 254 block programs ! - fast save : based on hypra-save (??) (don't know how fast is it compared to original) works with any device. Only tested with 1541 (I + II) and 1541 Ultimate. saves everything from ram under the roms and the IO. can save up to 254 block programs ! - list directory from disk without loosing loaded programs. replaces "PRG" with ",8,1" for easier loading (see function keys) - list the *REAL* content of the flash directory. The format of each content is the following: <loading start address> "<name>",1,1:<flash start address in hex> - default device from basic is 8, not 1 - "load" without filename loads the directory of device 8 - "save" prompts with a small dialog to enter the filename if no parameter is given. This is very useful for saving large files without getting the infamous "out of memory" error because basic cannot store the filename. The filename is stored on the stack. - function keys: F1 : list directory in empty line, loads a program if a filename is following. Easy to be used with listed directories (try it and you understand it what I mean). F2 : run F3 : sys 4096* 8 (cursor is placed on the "8" to edit) F4 : save F5 : submit a floppy command F6 : read floppy status F7 : list (is the right button of the DTV) F8 : tool menu - shift+run/stop (=esc) starts the first program on drive 8 - loading and saving addresses are printed in hex features of the tool menu: -change work device with F1 : this device is used for saving or all other disk operations -disable / enable fast load: : enable or disable the fast loader (and saver) for incompatible devices. "filecopy" in the menu is still using the fast loader -filecopy : can copy files from device 8 and the device 1 (the flash). uses extra memory. toggling the source device is done with F3 files are copied to work device select files with space, return to start -format : normal format (original from zipper of collision does not work very well) -validate : to validate disks selected by work device -scratch : scratch multiple files on work device select files with space, return to start -rename : rename file on work device select file with return -initialize : initialize command submitted to work device -floppy reset : resets the floppy and display the version number of the dos -re-new : simple old command for basic programs. prints the end of the basic program in hex. -jmp ($8000) : because of the kernal does not recognize the "CBM80" code at 0x8004, this function is included to run some old games that uses the reset vector for starting. "CBM80" is checked before at 0x8004 -CPU turbo on : enables the CPU turbo mode of the DTV (burst mode, no BAD line, shorter execution time for instructions) caution : some programs don't work with this (especially programs that uses the IEC bus), but normal basic save and load works with turbo mode now. -CPU turbo off: disable CPU turbo mode -mount d64 (ultimate only) : mount a D64 image from the 1541 ultimate. selection with return, abort with run/stop (=esc) can be used to change directory too if the selection will be aborted with run/stop -mount and kill (ultimate only) : like "mount d64", but kills the SD2IEC channel afterwards. This is useful for working fast loaders (like the internal one included in this kernal) -kill SD2IEC (ultimate only): kills the SD2IEC channel for using fast loaders -make d64 (ultimate only) : creates a blank d64 image on ultimate -fill whole mem: Fill the complete memory from 0x000800 to 0x1f8000 with a selectable byte to fill the memory with. -reenter to TMP-PTV : if you program with the Turbo Macro Pro Assembler (version is called "TMP PTV" then you have sometimes the following problem : your own code messed up the computer and the callback to get back into the TMP is lost after reset. This menu entry does enter to the TMP if it is recognized.
l'asta è partita veramente per la tangente! Guarda quanti rilanci!
assurdo pensavo fosse pazzo il tizio, e invece l'asta partiva da un onestissimo 80 Pounds, che sono schizzati a quasi 700 in poco tempo
Autore
Topic: Bufera Plus/4 passata, si parte col C64DTV :) (Letto 28701 volte)
